flexfax: HylaFAX v4.0pl2 can't send ???

[Thierry Coopman <thierry@skynet.be>]

I just installed the new patch level and now I can't send any fax out???

Feb 17 17:37:42.34: [  362]: SESSION BEGIN 00022231 XXXXXXXXXXXXX
Feb 17 17:37:42.34: [  362]: SEND FAX: JOB 7638 DEST XXXXXXXXX COMMID 00022231
Feb 17 17:37:42.34: [  362]: DELAY 2600 ms
Feb 17 17:37:44.95: [  362]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 17 17:37:45.14: [  362]: --> [2:OK]
Feb 17 17:37:45.14: [  362]: <-- [18:ATS8=2S7=60&D3&C1\r]
Feb 17 17:37:45.34: [  362]: --> [2:OK]
Feb 17 17:37:45.34: [  362]: <-- [12:AT+FCLASS=2\r]
Feb 17 17:37:45.50: [  362]: --> [2:OK]
Feb 17 17:37:45.50: [  362]: <-- [10:AT+FTBC=0\r]
Feb 17 17:37:45.66: [  362]: --> [2:OK]
Feb 17 17:37:45.66: [  362]: <-- [10:AT+FBOR=0\r]
Feb 17 17:37:45.82: [  362]: --> [2:OK]
Feb 17 17:37:45.82: [  362]: <-- [13:AT+FPHCTO=30\r]
Feb 17 17:37:45.98: [  362]: --> [2:OK]
Feb 17 17:37:45.98: [  362]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Feb 17 17:37:46.18: [  362]: --> [2:OK]
Feb 17 17:37:46.18: [  362]: <-- [5:ATM0\r]
Feb 17 17:37:46.34: [  362]: --> [2:OK]
Feb 17 17:37:46.42: [  362]: <-- [12:AT+FCLASS=2\r]
Feb 17 17:37:46.68: [  362]: --> [2:OK]
Feb 17 17:37:46.68: [  362]: <-- [10:AT+FTBC=0\r]
Feb 17 17:37:46.96: [  362]: --> [2:OK]
Feb 17 17:37:46.96: [  362]: <-- [10:AT+FBOR=0\r]
Feb 17 17:37:47.24: [  362]: --> [2:OK]
Feb 17 17:37:47.24: [  362]: <-- [13:AT+FPHCTO=30\r]
Feb 17 17:37:47.52: [  362]: --> [2:OK]
Feb 17 17:37:47.52: [  362]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Feb 17 17:37:47.80: [  362]: --> [2:OK]
Feb 17 17:37:47.80: [  362]: <-- [31:AT+FLID="Belgacom - Skynet nv"\r]
Feb 17 17:37:48.08: [  362]: --> [2:OK]
Feb 17 17:37:48.08: [  362]: DIAL 080020406
Feb 17 17:37:48.08: [  362]: <-- [17:ATDT0,XXXXXXXXX@\r]
Feb 17 17:39:00.60: [  362]: --> [8:+FHNG: 4]
Feb 17 17:39:00.60: [  362]: REMOTE HANGUP: Ringback detected, no answer (timeout) (code 4)
Feb 17 17:39:00.60: [  362]: SEND FAILED: Ringback detected, no answer (timeout)
Feb 17 17:39:00.60: [  362]: <-- [5:ATH0\r]
Feb 17 17:39:01.16: [  362]: --> [2:OK]
Feb 17 17:39:01.16: [  362]: SESSION END

All faxes are returned like that. Is there something I have to reconfigure?????

After all that that I get the folowing message
Your facsimile job to 080020406 was rejected because:
    REJECT: Too many attempts to transmit: 3, max 3

    ---- Unsent job status ----

   Destination: XXXXXXXX
         JobID: 7638
       GroupID: 7638
        Sender: Thierry
      Mailaddr: Thierry@skynet.be
        CommID: 00022245
Submitted From: localhost
    Page Width: 215 (mm)
   Page Length: 279 (mm)
    Resolution: 196 (lpi)
        Status: REJECT: Too many attempts to transmit: 3, max 3
       Dialogs: 3 (exchanges with remote device)
         Dials: 0 (consecutive failed calls to destination)
         Calls: 4 (total phone calls placed)
         Pages: 0 (pages transmitted)
      TotPages: 2 (total pages to transmit)
      Attempts: 0 (attempts to send current page)
        Dirnum: 0 (directory of next page to send)

    ---- Documents submitted for transmission ----

The following documents were submitted for transmission and are
available on the server for reuse until they are automatically
purged when this job is removed.  Documents may also be manually
removed using the faxrm command; consult faxrm(1) for information.

Filename                 Size Type
docq/doc7638.cover     240295 PostScript cover page
docq/doc12868.ps.7638   370554 PostScript
-----------

I use SupraFAX modem 28.8 and I sent the fax to our own faxnumber (cascade of 3 faxmachines). It worked well before with the pl1 but now it realy screws up :((

Thanks for helping me out (or pointing out stupid errors I made)



--
Thierry aka |Calvin|  - Belcast@skYNet.bE - Graphic Intelligence Crew -

My opinions are personal, and have really nothing or nothing to do with
Belgacom Skynet!

Belgacom Skynet NV/SA    Rue Colonel Bourgstraat 124   B-1140 Bruxelles
Phone. +32.2.706.11.11     Fax: +32.2.705.80.44   WWW: http://www.skynet.be