flexfax: Hylafax and Creatix modem

[Lothar Krau <Lothar_Krauss@compuserve.com>]

Andreas wrote:
> I canīt get my Creatix Phonemaster VF144 modem working together with Hylafax4.0 under > Linux. 
> Could you please help me to get the right initialisation codes (it has got a UMC 
> chipset).
> None of the ones I found, worked right!

Here is my config file for Creatix LC144. It works for outgoing and incomming faxes.

Lothar

CountryCode:            49
AreaCode:               69
FAXNumber:              +xx.xx.xxxxxxx
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         63
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          Medium
GettyArgs:              "%l"
LocalIdentifier:        "xxxxxxxxxxxxxxx"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "Von %%l|%%n|%d.%m.%Y %R|Seite %%p von %%t"
QualifyTSI:             ""
MaxRecvPages:           25
ModemType:              Class2          # use this to supply a hint
ModemRate:              19200           # max rate for DCE-DTE communication
ModemFlowControl:       xonxoff         # XON/XOFF flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
ModemDialCmd:           AT%%TCBDT%s     # Keine Wahlsperre bei Fehlversuchen
ModemResetCmds:         AT+FAA=1        # stuff to do when modem is reset
ModemResetDelay:        3500
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT&K0           # disable flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
ModemWaitForConnect:    true            # User-Name CONNECT existiert nicht
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH0            # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     MSB2LSB         # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for transmit
Use2D:                  No
Class2Cmd:              AT+FCLASS=2     # command to enter class 2
Class2BORCmd:           AT+FBOR=0       # bit order for phase B/C/D (direct)
Class2RELCmd:           AT+FREL=1       # byte-align EOL codes on recv
Class2CQCmd:            ""              # commands to enable copy quality proc.
Class2AbortCmd:         AT+FK           # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality capabilities
Class2DCCQueryCmd:      AT+FDCC=?       # query for modem capabilities
Class2TBCCmd:           AT+FTBC=0       # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FPHCTO=30    # set phase C timeout parameter
Class2BUGCmd:           AT+FBUG=1       # enable HDLC frame tracing
Class2LIDCmd:           AT+FLID         # set local identifier command
Class2DCCCmd:           AT+FDCC         # set modem capabilities command
Class2DISCmd:           AT+FDIS         # set session parameters command
Class2DDISCmd:          AT+FDIS         # Disable pre-dial DIS command hack
Class2CIGCmd:           AT+FCIG         # set polling identifier command
Class2PTSCmd:           AT+FPTS         # set post-page status command
Class2SPLCmd:           AT+FSPL         # set polling indicator command
Class2RecvDataTrigger:  "\022"          # character sent to modem to start recv
Class2XmitWaitForXON:   no              # if true, wait for XON before send
From: jay@dixonssurgical.co.uk (Jay Dixon)
To: flexfax@sgi.com
Subject: flexfax: Setup Problems
Date: Wed, 01 Oct 1997 16:11:25 GMT
Organization: Dixons Surgical Ltd
Reply-To: jay@dixonssurgical.co.uk
X-Mailer: Forte Agent 1.5/32.451
Sender: owner-flexfax@celestial.com

I am trying to set up a Hylafax v4.0pl1 server on FreeBSD 2.2.1 to
serve outgoing only for Win3.x/WinNT4.0 machines.  I have a Hayes
ACCURA 56K External Speakerphone Modem on cuaa0.  This is a class 1
fax device.  The cuaa0 dev is also used for PPP dialup to my ISP using
userPPP within FreeBSD.

I have got the software installed but the setup is still shaky.  I
have the hfaxd service setup in inetd on port 4559 and this is working
OK from boot (i.e. the Win machines can communicate and pass faxes
through).

I am starting faxq from the following script at bootup in
/usr/local/etc/rc.d/hylafax.sh -

if [ -x /usr/local/sbin/faxq ]; then
        /usr/local/sbin/faxq && echo 'Hylafax Server.'
fi

The faxq starts up OK but when I send a fax through it sits there
saying 'Modem cuaa0 (+44.(0)1268.764615): Waiting for modem to come
ready'.

If I then type '/usr/local/sbin/faxmodem cuaa0' at the command line
the modem then dials and sends the faxes OK.  What am I missing and
where?

Also after the modem has sent the fax it is staying in class1 mode and
I can't send data (i.e. make a PPP connection).  I have tried the
following strings in the 'ModemResetCmds' variable of
/var/spool/fax/etc/config.cuaa0 with no joy -

AT+FCALSS=0	# Set to Fax Class 0 (Data)
ATF		# Set to factory presets

Any ideas please?

Thanks
Jay

---------
Jay Dixon - Dixons Surgical Ltd - Wickford - Essex - England
jay@dixonssurgical.co.uk  -  http://www.dixonssurgical.co.uk