|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Problem faxing with Accura 336
hylafax-v4.0pl1 on Solaris 2.5.1 with gcc 2.7.2.1; Hayes Accura 336
Installed hylafax. Got it work with text-paging (SNPP/IXO) just fine,
but am still having trouble faxing. Once the modem connects to the fax
machine, it just continues to train to failure. I have not yet had a
successful fax. The modem says it supports only class 1 faxing and I'm
using software (xon/xoff) flow control. Read the FAQ, but didn't find
anything that seemed to match the problem I was having.
Any pointers/help would be apprecited! Thanks,
Joe
=======================config.cua_0====================================
CountryCode: 1
AreaCode: xxx
FAXNumber: +1.xxx.xxx.xxxx
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0xfffff
SessionTracing: 0x4f
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "InteliHealth"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
QualifyTSI: etc/tsi
MaxRecvPages: 25
Use2d: no
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
ModemRate: 2400
ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDT9%s
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "" # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&K0 # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#ModemSendBeginCmd: "<rts>"
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendPPMDelay: 75 # 75ms delay before sending PPM
Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
================================================================
Your facsimile job to 1xxxxxxxxx failed because:
Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page
---- Transcript of session follows ----
Jun 04 13:17:13.82: [28367]: SESSION BEGIN 00000004 1xxxxxxxxxx
Jun 04 13:17:13.82: [28367]: SEND FAX: JOB 1 DEST 1xxxxxxxxxx COMMID 00000004
Jun 04 13:17:13.82: [28367]: MODEM set DTR OFF
Jun 04 13:17:13.82: [28367]: DELAY 2600 ms
Jun 04 13:17:16.42: [28367]: MODEM set DTR ON
Jun 04 13:17:16.42: [28367]: MODEM set baud rate: 2400 baud, input flow XON/XOFF, output flow XON/XOFF
Jun 04 13:17:16.42: [28367]: MODEM flush i/o
Jun 04 13:17:16.42: [28367]: <-- [15:ATE0V1Q0S0=0H0\r]
Jun 04 13:17:16.78: [28367]: --> [2:OK]
Jun 04 13:17:16.79: [28367]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
Jun 04 13:17:17.15: [28367]: --> [2:OK]
Jun 04 13:17:17.15: [28367]: <-- [12:AT+FCLASS=1\r]
Jun 04 13:17:17.47: [28367]: --> [2:OK]
Jun 04 13:17:17.47: [28367]: <-- [5:ATM0\r]
Jun 04 13:17:17.76: [28367]: --> [2:OK]
Jun 04 13:17:17.76: [28367]: MODEM input buffering enabled
Jun 04 13:17:17.79: [28367]: <-- [12:AT+FCLASS=1\r]
Jun 04 13:17:18.21: [28367]: --> [2:OK]
Jun 04 13:17:18.21: [28367]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Jun 04 13:17:18.21: [28367]: DIAL 1xxxxxxxxxx
Jun 04 13:17:18.21: [28367]: <-- [17:ATDT91xxxxxxxxxx\r]
Jun 04 13:17:42.11: [28367]: --> [7:CONNECT]
Jun 04 13:17:42.11: [28367]: MODEM input buffering disabled
Jun 04 13:17:43.31: [28367]: --> HDLC<13:FF C0 04 B5 00 00 9E 19 85 11 4C 03 8B>
Jun 04 13:17:43.31: [28367]: --> [2:OK]
Jun 04 13:17:43.31: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:17:43.41: [28367]: --> [7:CONNECT]
Jun 04 13:17:44.13: [28367]: --> HDLC<34:FF C0 04 00 00 90 00 06 00 19 1E 24 15 1C 19 18 15 11 1C 24 18 0F 0F 0F 0F 0F 0F 0F 0F 0F 00 00 CE 2D>
Jun 04 13:17:44.28: [28367]: --> [2:OK]
Jun 04 13:17:44.28: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:17:44.37: [28367]: --> [7:CONNECT]
Jun 04 13:17:44.84: [28367]: --> HDLC<25:FF C0 02 6C 4C 1C 6C CC 1C 4C AC 8C 4C 04 04 04 04 04 04 04 04 04 04 1B 4A>
Jun 04 13:17:45.00: [28367]: --> [2:OK]
Jun 04 13:17:45.00: [28367]: REMOTE CSI "xxxxxxxxxx"
Jun 04 13:17:45.00: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:17:45.10: [28367]: --> [7:CONNECT]
Jun 04 13:17:45.15: [28367]: --> HDLC<9:FF C8 01 00 77 1D 22 9E F4>
Jun 04 13:17:45.31: [28367]: --> [2:OK]
Jun 04 13:17:45.31: [28367]: REMOTE best rate 14400 bit/s
Jun 04 13:17:45.31: [28367]: REMOTE max page width 1728 pixels in 215 mm
Jun 04 13:17:45.31: [28367]: REMOTE max unlimited page length
Jun 04 13:17:45.31: [28367]: REMOTE best vres 7.7 line/mm
Jun 04 13:17:45.31: [28367]: REMOTE best format 2-D MMR
Jun 04 13:17:45.31: [28367]: REMOTE supports T.30 Annex A, ECM
Jun 04 13:17:45.31: [28367]: REMOTE best 20 ms, 10 ms/scanline
Jun 04 13:17:45.31: [28367]: USE 14400 bit/s
Jun 04 13:17:45.31: [28367]: USE 20 ms, 10 ms/scanline
Jun 04 13:17:45.31: [28367]: SEND file "docq/doc1.ps;30"
Jun 04 13:17:45.31: [28367]: USE page width 1728 pixels in 215 mm
Jun 04 13:17:45.31: [28367]: USE unlimited page length
Jun 04 13:17:45.31: [28367]: USE 3.85 line/mm
Jun 04 13:17:45.31: [28367]: USE 1-D MR
Jun 04 13:17:45.31: [28367]: SEND training at v.17 14400 bit/s
Jun 04 13:17:45.32: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:17:46.51: [28367]: --> [7:CONNECT]
Jun 04 13:17:46.51: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:17:47.51: [28367]: --> [7:CONNECT]
Jun 04 13:17:47.51: [28367]: <-- HDLC<6:FF C8 C1 00 44 10>
Jun 04 13:17:48.05: [28367]: --> [2:OK]
Jun 04 13:17:48.06: [28367]: DELAY 75 ms
Jun 04 13:17:48.13: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:17:48.13: [28367]: <-- [11:AT+FTM=145\r]
Jun 04 13:17:49.98: [28367]: --> [7:CONNECT]
Jun 04 13:18:01.57: [28367]: --> [2:OK]
Jun 04 13:18:01.57: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:18:01.57: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:18:04.67: [28367]: --> [0:]
Jun 04 13:18:04.67: [28367]: MODEM <Empty line>
Jun 04 13:18:04.67: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:18:04.85: [28367]: --> [2:OK]
Jun 04 13:18:04.85: [28367]: DELAY 1500 ms
Jun 04 13:18:06.34: [28367]: SEND training at v.17 14400 bit/s
Jun 04 13:18:06.34: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:18:07.51: [28367]: --> [7:CONNECT]
Jun 04 13:18:07.51: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:18:08.52: [28367]: --> [7:CONNECT]
Jun 04 13:18:08.52: [28367]: <-- HDLC<6:FF C8 C1 00 44 10>
Jun 04 13:18:09.07: [28367]: --> [2:OK]
Jun 04 13:18:09.07: [28367]: DELAY 75 ms
Jun 04 13:18:09.14: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:18:09.14: [28367]: <-- [11:AT+FTM=145\r]
Jun 04 13:18:11.00: [28367]: --> [7:CONNECT]
Jun 04 13:18:22.58: [28367]: --> [2:OK]
Jun 04 13:18:22.58: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:18:22.58: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:18:25.68: [28367]: --> [0:]
Jun 04 13:18:25.69: [28367]: MODEM <Empty line>
Jun 04 13:18:25.69: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:18:25.86: [28367]: --> [2:OK]
Jun 04 13:18:25.86: [28367]: DELAY 1500 ms
Jun 04 13:18:27.35: [28367]: SEND training at v.17 12000 bit/s
Jun 04 13:18:27.36: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:18:28.51: [28367]: --> [7:CONNECT]
Jun 04 13:18:28.51: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:18:29.53: [28367]: --> [7:CONNECT]
Jun 04 13:18:29.53: [28367]: <-- HDLC<6:FF C8 C1 00 54 10>
Jun 04 13:18:30.08: [28367]: --> [2:OK]
Jun 04 13:18:30.08: [28367]: DELAY 75 ms
Jun 04 13:18:30.16: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:18:30.16: [28367]: <-- [11:AT+FTM=121\r]
Jun 04 13:18:32.01: [28367]: --> [7:CONNECT]
Jun 04 13:18:41.70: [28367]: --> [2:OK]
Jun 04 13:18:41.70: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:18:41.70: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:18:44.81: [28367]: --> [0:]
Jun 04 13:18:44.81: [28367]: MODEM <Empty line>
Jun 04 13:18:44.81: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:18:44.98: [28367]: --> [2:OK]
Jun 04 13:18:44.99: [28367]: DELAY 1500 ms
Jun 04 13:18:46.48: [28367]: SEND training at v.17 12000 bit/s
Jun 04 13:18:46.48: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:18:47.71: [28367]: --> [7:CONNECT]
Jun 04 13:18:47.71: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:18:48.73: [28367]: --> [7:CONNECT]
Jun 04 13:18:48.73: [28367]: <-- HDLC<6:FF C8 C1 00 54 10>
Jun 04 13:18:49.28: [28367]: --> [2:OK]
Jun 04 13:18:49.28: [28367]: DELAY 75 ms
Jun 04 13:18:49.36: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:18:49.36: [28367]: <-- [11:AT+FTM=121\r]
Jun 04 13:18:51.21: [28367]: --> [7:CONNECT]
Jun 04 13:19:00.90: [28367]: --> [2:OK]
Jun 04 13:19:00.90: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:19:00.90: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:19:04.01: [28367]: --> [0:]
Jun 04 13:19:04.01: [28367]: MODEM <Empty line>
Jun 04 13:19:04.01: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:19:04.19: [28367]: --> [2:OK]
Jun 04 13:19:04.19: [28367]: DELAY 1500 ms
Jun 04 13:19:05.68: [28367]: SEND training at v.17 9600 bit/s
Jun 04 13:19:05.68: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:19:06.91: [28367]: --> [7:CONNECT]
Jun 04 13:19:06.91: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:19:07.93: [28367]: --> [7:CONNECT]
Jun 04 13:19:07.93: [28367]: <-- HDLC<6:FF C8 C1 00 64 10>
Jun 04 13:19:08.48: [28367]: --> [2:OK]
Jun 04 13:19:08.48: [28367]: DELAY 75 ms
Jun 04 13:19:08.55: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:19:08.55: [28367]: <-- [10:AT+FTM=97\r]
Jun 04 13:19:10.40: [28367]: --> [7:CONNECT]
Jun 04 13:19:18.19: [28367]: --> [2:OK]
Jun 04 13:19:18.19: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:19:18.20: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:19:21.30: [28367]: --> [0:]
Jun 04 13:19:21.30: [28367]: MODEM <Empty line>
Jun 04 13:19:21.30: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:19:21.48: [28367]: --> [2:OK]
Jun 04 13:19:21.48: [28367]: DELAY 1500 ms
Jun 04 13:19:22.97: [28367]: SEND training at v.17 9600 bit/s
Jun 04 13:19:22.97: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:19:24.21: [28367]: --> [7:CONNECT]
Jun 04 13:19:24.21: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:19:25.22: [28367]: --> [7:CONNECT]
Jun 04 13:19:25.22: [28367]: <-- HDLC<6:FF C8 C1 00 64 10>
Jun 04 13:19:25.76: [28367]: --> [2:OK]
Jun 04 13:19:25.76: [28367]: DELAY 75 ms
Jun 04 13:19:25.84: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:19:25.84: [28367]: <-- [10:AT+FTM=97\r]
Jun 04 13:19:27.69: [28367]: --> [7:CONNECT]
Jun 04 13:19:35.49: [28367]: --> [2:OK]
Jun 04 13:19:35.49: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:19:35.49: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:19:38.59: [28367]: --> [0:]
Jun 04 13:19:38.59: [28367]: MODEM <Empty line>
Jun 04 13:19:38.60: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:19:38.77: [28367]: --> [2:OK]
Jun 04 13:19:38.77: [28367]: DELAY 1500 ms
Jun 04 13:19:40.26: [28367]: SEND training at v.17 7200 bit/s
Jun 04 13:19:40.27: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:19:41.41: [28367]: --> [7:CONNECT]
Jun 04 13:19:41.41: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:19:42.42: [28367]: --> [7:CONNECT]
Jun 04 13:19:42.42: [28367]: <-- HDLC<6:FF C8 C1 00 74 10>
Jun 04 13:19:42.96: [28367]: --> [2:OK]
Jun 04 13:19:42.96: [28367]: DELAY 75 ms
Jun 04 13:19:43.04: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:19:43.05: [28367]: <-- [10:AT+FTM=73\r]
Jun 04 13:19:44.89: [28367]: --> [7:CONNECT]
Jun 04 13:19:50.79: [28367]: --> [2:OK]
Jun 04 13:19:50.79: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:19:50.80: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:19:53.90: [28367]: --> [0:]
Jun 04 13:19:53.90: [28367]: MODEM <Empty line>
Jun 04 13:19:53.90: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:19:54.07: [28367]: --> [2:OK]
Jun 04 13:19:54.07: [28367]: DELAY 1500 ms
Jun 04 13:19:55.57: [28367]: SEND training at v.17 7200 bit/s
Jun 04 13:19:55.57: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:19:56.71: [28367]: --> [7:CONNECT]
Jun 04 13:19:56.71: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:19:57.72: [28367]: --> [7:CONNECT]
Jun 04 13:19:57.72: [28367]: <-- HDLC<6:FF C8 C1 00 74 10>
Jun 04 13:19:58.27: [28367]: --> [2:OK]
Jun 04 13:19:58.27: [28367]: DELAY 75 ms
Jun 04 13:19:58.35: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:19:58.35: [28367]: <-- [10:AT+FTM=73\r]
Jun 04 13:20:00.20: [28367]: --> [7:CONNECT]
Jun 04 13:20:06.10: [28367]: --> [2:OK]
Jun 04 13:20:06.10: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:20:06.10: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:20:09.20: [28367]: --> [0:]
Jun 04 13:20:09.20: [28367]: MODEM <Empty line>
Jun 04 13:20:09.20: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:20:09.38: [28367]: --> [2:OK]
Jun 04 13:20:09.38: [28367]: DELAY 1500 ms
Jun 04 13:20:10.87: [28367]: SEND training at v.27ter 4800 bit/s
Jun 04 13:20:10.87: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:20:12.11: [28367]: --> [7:CONNECT]
Jun 04 13:20:12.11: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:20:13.13: [28367]: --> [7:CONNECT]
Jun 04 13:20:13.13: [28367]: <-- HDLC<6:FF C8 C1 00 50 10>
Jun 04 13:20:13.67: [28367]: --> [2:OK]
Jun 04 13:20:13.67: [28367]: DELAY 75 ms
Jun 04 13:20:13.75: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:20:13.75: [28367]: <-- [10:AT+FTM=48\r]
Jun 04 13:20:14.92: [28367]: --> [7:CONNECT]
Jun 04 13:20:18.92: [28367]: --> [2:OK]
Jun 04 13:20:18.92: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:20:18.92: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:20:22.03: [28367]: --> [0:]
Jun 04 13:20:22.03: [28367]: MODEM <Empty line>
Jun 04 13:20:22.03: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:20:22.21: [28367]: --> [2:OK]
Jun 04 13:20:22.21: [28367]: DELAY 1500 ms
Jun 04 13:20:23.70: [28367]: SEND training at v.27ter 4800 bit/s
Jun 04 13:20:23.70: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:20:24.91: [28367]: --> [7:CONNECT]
Jun 04 13:20:24.91: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:20:25.92: [28367]: --> [7:CONNECT]
Jun 04 13:20:25.92: [28367]: <-- HDLC<6:FF C8 C1 00 50 10>
Jun 04 13:20:26.46: [28367]: --> [2:OK]
Jun 04 13:20:26.46: [28367]: DELAY 75 ms
Jun 04 13:20:26.54: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:20:26.54: [28367]: <-- [10:AT+FTM=48\r]
Jun 04 13:20:27.71: [28367]: --> [7:CONNECT]
Jun 04 13:20:31.71: [28367]: --> [2:OK]
Jun 04 13:20:31.71: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:20:31.71: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:20:34.82: [28367]: --> [0:]
Jun 04 13:20:34.82: [28367]: MODEM <Empty line>
Jun 04 13:20:34.82: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:20:35.00: [28367]: --> [2:OK]
Jun 04 13:20:35.00: [28367]: DELAY 1500 ms
Jun 04 13:20:36.49: [28367]: SEND training at v.27ter fallback mode 2400 bit/s
Jun 04 13:20:36.49: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:20:37.71: [28367]: --> [7:CONNECT]
Jun 04 13:20:37.71: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:20:38.71: [28367]: --> [7:CONNECT]
Jun 04 13:20:38.71: [28367]: <-- HDLC<6:FF C8 C1 00 40 10>
Jun 04 13:20:39.26: [28367]: --> [2:OK]
Jun 04 13:20:39.26: [28367]: DELAY 75 ms
Jun 04 13:20:39.33: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:20:39.33: [28367]: <-- [10:AT+FTM=24\r]
Jun 04 13:20:40.74: [28367]: --> [7:CONNECT]
Jun 04 13:20:42.84: [28367]: --> [2:OK]
Jun 04 13:20:42.84: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:20:42.84: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:20:45.95: [28367]: --> [0:]
Jun 04 13:20:45.95: [28367]: MODEM <Empty line>
Jun 04 13:20:45.95: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:20:46.13: [28367]: --> [2:OK]
Jun 04 13:20:46.13: [28367]: DELAY 1500 ms
Jun 04 13:20:47.62: [28367]: SEND training at v.27ter fallback mode 2400 bit/s
Jun 04 13:20:47.62: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:20:48.81: [28367]: --> [7:CONNECT]
Jun 04 13:20:48.81: [28367]: <-- HDLC<23:FF C0 C2 16 2E 36 86 A6 12 96 36 A6 2E 76 92 04 04 04 04 04 04 04 04>
Jun 04 13:20:49.83: [28367]: --> [7:CONNECT]
Jun 04 13:20:49.83: [28367]: <-- HDLC<6:FF C8 C1 00 40 10>
Jun 04 13:20:50.38: [28367]: --> [2:OK]
Jun 04 13:20:50.38: [28367]: DELAY 75 ms
Jun 04 13:20:50.45: [28367]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jun 04 13:20:50.45: [28367]: <-- [10:AT+FTM=24\r]
Jun 04 13:20:51.86: [28367]: --> [7:CONNECT]
Jun 04 13:20:53.96: [28367]: --> [2:OK]
Jun 04 13:20:53.96: [28367]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jun 04 13:20:53.97: [28367]: <-- [9:AT+FRH=3\r]
Jun 04 13:20:57.07: [28367]: --> [0:]
Jun 04 13:20:57.08: [28367]: MODEM <Empty line>
Jun 04 13:20:57.08: [28367]: MODEM TIMEOUT: waiting for v.21 carrier
Jun 04 13:20:57.25: [28367]: --> [2:OK]
Jun 04 13:20:57.25: [28367]: DELAY 1500 ms
Jun 04 13:20:58.74: [28367]: TRAINING failed
Jun 04 13:20:58.75: [28367]: SEND: Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page "docq/doc1.ps;30", dirnum 0
Jun 04 13:20:58.75: [28367]: <-- [9:AT+FTH=3\r]
Jun 04 13:20:59.91: [28367]: --> [7:CONNECT]
Jun 04 13:20:59.91: [28367]: <-- HDLC<3:FF C8 DF>
Jun 04 13:21:00.37: [28367]: --> [2:OK]
Jun 04 13:21:00.37: [28367]: MODEM input buffering enabled
Jun 04 13:21:00.37: [28367]: <-- [5:ATH0\r]
Jun 04 13:21:00.69: [28367]: --> [2:OK]
Jun 04 13:21:00.69: [28367]: MODEM set DTR OFF
Jun 04 13:21:00.69: [28367]: SESSION END
