Re: squished faxes when receiving a fax

[High Mercury <merc@icanect.net>]

> >  Date: Sun, 11 May 1997 01:49:50 -0400 (EDT)
> >  From: High Mercury <merc@icanect.net>
> >  I am using a multitech2834MR modem to receive faxes and when I receive
> >  a fax using 4.0pl1, they only take up half the page. Here is the log of the
> >  reception:
> 
> Sounds like a flow control problem - try changing from whatever you're
> using to the to the other method (i.e., if you're using RTSCTS, try XONXOFF).

I tried switching it to xonxoff but received the same fax squished into
1/2 a page: 

---------------------------------------------------------------------------
May 13 21:12:20.23: [ 6281]: SESSION BEGIN 00003299 1xxxxxxxxx
May 13 21:12:20.24: [ 6281]: <-- [4:ATA\r]
May 13 21:12:27.40: [ 6281]: --> [74:+FHT:FF 03 40 37 30 38 30 30 32 36 35 30 33
 20 20 20 20 20 20 20 20 20 20 ]
May 13 21:12:28.19: [ 6281]: --> [26:+FHT:FF 13 80 00 6E FA 00 ]
May 13 21:12:28.96: [ 6281]: --> [5:+FCON]
May 13 21:12:28.96: [ 6281]: STATE CHANGE: ANSWERING -> RECEIVING
May 13 21:12:28.96: [ 6281]: MODEM input buffering enabled
May 13 21:12:28.97: [ 6281]: RECV FAX: begin
May 13 21:12:30.64: [ 6281]: --> [74:+FHR:FF 03 43 37 32 32 32 31 32 36 35 30 33
 20 20 20 20 20 20 20 20 20 20 ]
May 13 21:12:30.90: [ 6281]: --> [26:+FHR:FF 13 83 00 22 98 00 ]
May 13 21:12:34.18: [ 6281]: --> [28:+FTSI:"          xxxxxxxxxx"]
May 13 21:12:34.18: [ 6281]: REMOTE TSI "xxxxxxxxxx"
May 13 21:12:34.18: [ 6281]: --> [21:+FDCS:0,5,0,2,0,0,0,1]
May 13 21:12:34.18: [ 6281]: REMOTE wants 14400 bit/s
May 13 21:12:34.18: [ 6281]: REMOTE wants page width 1728 pixels in 215 mm
May 13 21:12:34.18: [ 6281]: REMOTE wants unlimited page length 
May 13 21:12:34.18: [ 6281]: REMOTE wants 3.85 line/mm
May 13 21:12:34.18: [ 6281]: REMOTE wants 1-D MR
May 13 21:12:34.18: [ 6281]: --> [2:OK]
May 13 21:12:34.18: [ 6281]: <-- [7:AT+FDR\r]
May 13 21:12:35.28: [ 6281]: --> [14:+FHT:FF 13 84 ]
May 13 21:12:35.57: [ 6281]: --> [5:+FCFR]
May 13 21:12:35.57: [ 6281]: --> [28:+FTSI:"          xxxxxxxxxx"]
May 13 21:12:35.57: [ 6281]: REMOTE TSI "xxxxxxxxxx"
May 13 21:12:35.57: [ 6281]: --> [21:+FDCS:0,5,0,2,0,0,0,1]
May 13 21:12:35.57: [ 6281]: REMOTE wants 14400 bit/s
May 13 21:12:35.57: [ 6281]: REMOTE wants page width 1728 pixels in 215 mm
May 13 21:12:35.57: [ 6281]: REMOTE wants unlimited page length 
May 13 21:12:35.57: [ 6281]: REMOTE wants 3.85 line/mm
May 13 21:12:35.57: [ 6281]: REMOTE wants 1-D MR
May 13 21:12:36.31: [ 6281]: --> [7:CONNECT]
May 13 21:12:36.31: [ 6281]: RECV: begin page
May 13 21:12:36.31: [ 6281]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
May 13 21:12:36.31: [ 6281]: RECV: send trigger 022
May 13 21:12:36.31: [ 6281]: <-- data [1]
May 13 21:12:52.70: [ 6281]: RECV: 29242 bytes of data, 1056 total lines
May 13 21:12:52.70: [ 6281]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled
May 13 21:12:52.70: [ 6281]: --> [18:+FPTS:1,1056,0,0,0]
May 13 21:12:53.91: [ 6281]: --> [14:+FHR:FF 13 2F ]
May 13 21:12:53.91: [ 6281]: --> [6:+FET:2]
May 13 21:12:53.91: [ 6281]: RECV recv EOP (no more pages or documents)
May 13 21:12:53.91: [ 6281]: --> [2:OK]
May 13 21:12:53.91: [ 6281]: RECV send MCF (message confirmation)
May 13 21:12:53.92: [ 6281]: <-- [7:AT+FDR\r]
May 13 21:12:55.08: [ 6281]: --> [14:+FHT:FF 13 8C ]
May 13 21:12:56.06: [ 6281]: RECV FAX: end
May 13 21:12:56.07: [ 6281]: SESSION END
---------------------------------------------------------------------------

Like I said before, this only happens when the fax machine is sending a
fax to the multitech modem in standard mode.  The weird thing though, is that
I can send a standard fax from the modem to the fax machine I'm using to
test and it takes up the whole page and is not squished.

Any other ideas??

thanks

merc