Problems receiving faxes

[Gregor Longariva <grlongar@cip.informatik.uni-erlangen.de>]

Hello!

I have problems to receive faxes. The strange thing ist, that the
faxes will be received correctly from another modem that I have here.
But today someone send me a fax and it appears only a few lines.
I use Class2DDISCmd:      AT+FDIS
I've tryed with ModemRecvFillOrder:     MSB2LSB an LSB2MSB
and Class2BORCmd:       AT+FBOR=0 or 1

The configuration below works for receiving faxes from my other modem
(which do not run under HylaFax).

Another strange thing ist, that I must use
   Use2D:              no
to be able sending faxes (to my other modem)

Can anybody help me?

(I have a noname modem with a Rockwell 144dp)

Thnax!

Here's the session log for the fax, I can't read:
May 13 09:32:57.74: [10546]: MODEM set baud rate: 19200 baud (flow control
unchanged)
May 13 09:32:57.96: [10546]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
May 13 09:32:57.96: [10546]: MODEM input buffering enabled
May 13 09:32:58.04: [10546]: RECV FAX: begin
May 13 09:32:59.76: [10546]: REMOTE TSI "xxxxxxxxxxxx"
May 13 09:32:59.76: [10546]: REMOTE wants 14400 bit/s
May 13 09:32:59.76: [10546]: REMOTE wants page width 1728 pixels in 215 mm
May 13 09:32:59.76: [10546]: REMOTE wants unlimited page length
May 13 09:32:59.76: [10546]: REMOTE wants 7.7 line/mm
May 13 09:32:59.76: [10546]: REMOTE wants 1-D MR
May 13 09:33:04.36: [10546]: REMOTE TSI "xxxxxxxxxxxx"
May 13 09:33:04.36: [10546]: REMOTE wants 14400 bit/s
May 13 09:33:04.36: [10546]: REMOTE wants page width 1728 pixels in 215 mm
May 13 09:33:04.36: [10546]: REMOTE wants unlimited page length
May 13 09:33:04.36: [10546]: REMOTE wants 7.7 line/mm
May 13 09:33:04.36: [10546]: REMOTE wants 1-D MR
May 13 09:33:05.09: [10546]: RECV: begin page
May 13 09:33:05.11: [10546]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
May 13 09:33:05.11: [10546]: RECV: send trigger 022
May 13 09:33:15.84: [10546]: RECV: 18439 bytes of data, 84 total lines
May 13 09:33:15.86: [10546]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
May 13 09:33:17.24: [10546]: RECV recv EOP (no more pages or documents)
May 13 09:33:17.28: [10546]: RECV send MCF (message confirmation)
May 13 09:33:20.86: [10546]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
May 13 09:33:38.47: [10546]: RECV FAX: end
May 13 09:33:38.63: [10546]: SESSION END

And here is my configuration:

Use2D:              no
ModemType:      Class2      # use this to supply a hint
ModemRate:      38400
ModemFlowControl:   rtscts
ModemSetupDTRCmd:   AT&D3       # setup so DTR drop resets modem
ModemSetupDCDCmd:   AT&C1       # setup so DCD reflects carrier (or not)
ModemDialCmd:       ATX1DT0%s
ModemResetCmds:     ""      # stuff to do when modem is reset
ModemAnswerCmd:     ATA     # use this to answer phone
ModemNoFlowCmd:     AT&K        # disable flow control cmd
ModemHardFlowCmd:   AT&K3       # hardware flow control cmd
ModemSoftFlowCmd:   AT&K4       # software flow control cmd
#ModemNoAutoAnswerCmd:  ATS0=0      # disable auto-answer
ModemSoftFlowCmd:   AT&S1\G0\Q3\X1
ModemSetVolumeCmd:  "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:    ATE0        # disable command echo
ModemVerboseResultsCmd: ATV1        # enable verbose command results
ModemResultCodesCmd:    ATQ0        # enable result codes
ModemOnHookCmd:     ATH0        # place phone on hook (hangup)
ModemSoftResetCmd:  ATZ     # do soft reset of modem
ModemWaitTimeCmd:   ATS7=80     # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2      # comma pause time is 2 seconds
ModemRecvFillOrder:     MSB2LSB     # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB     # bit order modem expects for transmit
ModemSetupAACmd:    AT+FAA=1+FCLASS=0 # enable adaptive answer in current
class ###
ModemAnswerFaxBeginCmd: "<19200><xon>" # modem switches on fax receive
Class2Cmd:          AT+FCLASS=2 # command to enter class 2
Class2BORCmd:       AT+FBOR=0   # bit order for phase B/C/D (direct)
Class2RELCmd:       AT+FREL=1   # byte-align EOL codes on recv
Class2CQCmd:        ""      # commands to enable copy quality proc.
Class2AbortCmd:     AT+FK       # abort session command
#Class2CQQueryCmd:  AT+FCQ=?    # query for copy quality capabilities
Class2CQQueryCmd:   ""
Class2DCCQueryCmd:  AT+FDCC=?   # query for modem capabilities
#Class2TBCCmd:      AT+FTBC=0   # setup stream mode
Class2CRCmd:        AT+FCR=1    # enable capability to receive
#Class2PHCTOCmd:        AT+FPHCTO=30    # set phase C timeout parameter
Class2PHCTOCmd:     ""
Class2BUGCmd:       AT+FBUG=1   # enable HDLC frame tracing
Class2LIDCmd:       AT+FLID     # set local identifier command
Class2DCCCmd:       AT+FDCC     # set modem capabilities command
Class2DISCmd:       AT+FDIS     # set session parameters command
#Class2DDISCmd:     ""      # disable pre-dial DIS command hack
Class2DDISCmd:      AT+FDIS
Class2CIGCmd:       AT+FCIG     # set polling identifier command
Class2PTSCmd:       AT+FPTS     # set post-page status command
Class2SPLCmd:       AT+FSPL     # set polling indicator command
Class2RecvDataTrigger:  "\022"      # character sent to modem to start recv
Class2XmitWaitForXON:   yes     # if true, wait for XON before send
ModemWaitForConnect:    yesLiebe Gruesse

     Gregor
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Gregor Longariva <grlongar@cip.informatik.uni-erlangen.de>