Probs using 2-D MR on transmission

[Fred Meyer <fred@mediswitch.co.za>]

Hi folks,

...i'm using HylaFAX v4.0pl1 build from source on a Linux box.
The Faxmodem is a MultiTech MT2834ZDXI, which should support 2-D MR
transmissions.

When connecting to a remote fax, that reports itself as 2-D capable,
HylaFAX still selects 1-D MR.

...actually i went for this modem because of this feature...and here in
SA the MT-modem is twice the price of an USR :(

...any hints?...i'll attach a logfile at the end of this mail....

TIA,
   Fred

-----Hylafax-logfile----------------- 
Apr 25 10:59:04.58: [ 2841]: SESSION BEGIN 00000071 27112393701
Apr 25 10:59:04.59: [ 2841]: SEND FAX: JOB 7 DEST xxxxxx COMMID 00000071
Apr 25 10:59:04.59: [ 2841]: DELAY 2600 ms
Apr 25 10:59:07.20: [ 2841]: <-- [15:ATE0V1Q0S0=0H0\r]
Apr 25 10:59:07.41: [ 2841]: --> [14:ATE0V1Q0S0=0H0]
Apr 25 10:59:07.41: [ 2841]: --> [2:OK]
Apr 25 10:59:07.41: [ 2841]: <-- [21:ATS8=2S7=60&E4&D3&C1\r]
Apr 25 10:59:07.58: [ 2841]: --> [2:OK]
Apr 25 10:59:07.58: [ 2841]: <-- [12:AT+FCLASS=2\r]
Apr 25 10:59:07.74: [ 2841]: --> [2:OK]
Apr 25 10:59:07.74: [ 2841]: <-- [10:AT+FTBC=0\r]
Apr 25 10:59:07.90: [ 2841]: --> [2:OK]
Apr 25 10:59:07.90: [ 2841]: <-- [10:AT+FBOR=0\r]
Apr 25 10:59:08.06: [ 2841]: --> [2:OK]
Apr 25 10:59:08.06: [ 2841]: <-- [13:AT+FPHCTO=30\r]
Apr 25 10:59:08.22: [ 2841]: --> [2:OK]
Apr 25 10:59:08.22: [ 2841]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Apr 25 10:59:08.39: [ 2841]: --> [2:OK]
Apr 25 10:59:08.39: [ 2841]: <-- [5:ATM0\r]
Apr 25 10:59:08.55: [ 2841]: --> [2:OK]
Apr 25 10:59:08.55: [ 2841]: <-- [12:AT+FCLASS=2\r]
Apr 25 10:59:08.82: [ 2841]: --> [2:OK]
Apr 25 10:59:08.82: [ 2841]: <-- [10:AT+FTBC=0\r]
Apr 25 10:59:09.08: [ 2841]: --> [2:OK]
Apr 25 10:59:09.08: [ 2841]: <-- [10:AT+FBOR=0\r]
Apr 25 10:59:09.34: [ 2841]: --> [2:OK]
Apr 25 10:59:09.34: [ 2841]: <-- [13:AT+FPHCTO=30\r]
Apr 25 10:59:09.60: [ 2841]: --> [2:OK]
Apr 25 10:59:09.60: [ 2841]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Apr 25 10:59:09.87: [ 2841]: --> [2:OK]
Apr 25 10:59:09.87: [ 2841]: <-- [31:AT+FLID="abcdefghijk"\r]
Apr 25 10:59:10.14: [ 2841]: --> [2:OK]
Apr 25 10:59:10.14: [ 2841]: DIAL xxxxxx
Apr 25 10:59:10.14: [ 2841]: <-- [13:ATDTxxxxxxx@\r]
Apr 25 10:59:27.51: [ 2841]: --> [5:+FCON]
[...]
Apr 25 10:59:30.69: [ 2841]: --> [21:+FDIS:1,3,0,2,1,0,0,2]
Apr 25 10:59:30.69: [ 2841]: --> [2:OK]
Apr 25 10:59:30.69: [ 2841]: REMOTE best rate 9600 bit/s
Apr 25 10:59:30.69: [ 2841]: REMOTE max page width 1728 pixels in 215 mm
Apr 25 10:59:30.69: [ 2841]: REMOTE max unlimited page length 
Apr 25 10:59:30.69: [ 2841]: REMOTE best vres 7.7 line/mm
Apr 25 10:59:30.69: [ 2841]: REMOTE best format 2-D MR
Apr 25 10:59:30.69: [ 2841]: REMOTE best 10 ms, 5 ms/scanline
Apr 25 10:59:30.69: [ 2841]: USE 9600 bit/s
Apr 25 10:59:30.69: [ 2841]: USE 10 ms, 5 ms/scanline
Apr 25 10:59:30.69: [ 2841]: SEND file "docq/doc55.ps;00"
Apr 25 10:59:30.93: [ 2841]: USE page width 1728 pixels in 215 mm
Apr 25 10:59:30.93: [ 2841]: USE unlimited page length 
Apr 25 10:59:30.93: [ 2841]: USE 3.85 line/mm
Apr 25 10:59:30.93: [ 2841]: USE 1-D MR
Apr 25 10:59:30.93: [ 2841]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,2\r]
Apr 25 10:59:31.20: [ 2841]: --> [2:OK]
Apr 25 10:59:31.20: [ 2841]: <-- [7:AT+FDT\r]
Apr 25 10:59:37.04: [ 2841]: --> [21:+FDCS:0,3,0,2,0,0,0,3]
Apr 25 10:59:37.04: [ 2841]: --> [7:CONNECT]
Apr 25 10:59:37.04: [ 2841]: SEND wait for XON
Apr 25 10:59:37.04: [ 2841]: --> [1:^Q]
Apr 25 10:59:37.04: [ 2841]: SEND begin page
Apr 25 10:59:37.11: [ 2841]: <-- data [1028]
[...]