Class 1 Rotary Fax Data ?

[Dan and Joanne Tucker <danjo@xnet.com>]

Well, I haven't got any further!

I am running : 
Linux 2.0.28 
Diald 0.15.2 
Hayes OPTIMA 28.8 V.34/V.FC+FAX

I can Send and Receive Faxes fine.  I can call out using Diald and
PPP fine.  I just can't get the thing to AnswerRotary.  Well, it
does kind of 8-)

------------------------  Hacked Messages ------------------
odhrerir diald[16524]: Running connect (pid = 16697).
odhrerir connect: Initializing Modem
odhrerir FaxGetty[15611]: ANSWER: Can not lock modem device

I expect this - - - - - - -       ^^^^^^^^^^^^^^^^^^^^^^^^^

odhrerir connect: Dialing system
odhrerir connect: Connected
odhrerir connect: Loggin in
odhrerir connect: Protocol started
odhrerir diald[16524]: Running pppd (pid = 16708).
odhrerir pppd[16708]: pppd 2.2.0 started by root, uid 0
odhrerir pppd[16708]: Using interface ppp0
odhrerir pppd[16708]: Connect: ppp0 <--> /dev/ttyS1
odhrerir pppd[16708]: local  IP address xxx.xxx.xxx.xxx
odhrerir pppd[16708]: remote IP address xxx.xxx.xxx.xxx

I surf like CRAZY 8-)  Now I am done.

odhrerir diald[16524]: Closing down idle link.
odhrerir pppd[16708]: Terminating on signal 2.
odhrerir pppd[16708]: Connection terminated.
odhrerir pppd[16708]: Exit.
odhrerir diald[16524]: Delaying 30 seconds before clear to dial.
odhrerir FaxGetty[15611]: MODEM ROCKWELL RC288DPi/04-00879-540 49416 PASS 
    04-00880-540 49416 PASS 40-00575-05 16683 PASS 40-00575-05 13625 PASS
odhrerir diald[16524]: FIFO. Termination request received.

I have Diald shut down after each call and reset.
Now I try to dial into the machine.

odhrerir FaxGetty[15611]: ANSWER: FAX CONNECTION
odhrerir FaxGetty[15611]: ANSWER: Ring detected without successful handshake

I expect this too. Now I expect it to try Data connect.

odhrerir FaxGetty[15611]: MODEM ROCKWELL etc.
odhrerir FaxGetty[15611]: ANSWER: FAX CONNECTION

?????????????????????????????????????????????????

odhrerir FaxGetty[15611]: ANSWER: Ring detected without successful handshake
odhrerir FaxGetty[15611]: MODEM ROCKWELL etc.
odhrerir FaxGetty[15611]: ANSWER: FAX CONNECTION

?????????????????????????????????????????????????

odhrerir FaxGetty[15611]: ANSWER: Ring detected without successful handshake
odhrerir FaxGetty[15611]: MODEM ROCKWELL etc.
odhrerir FaxGetty[15611]: ANSWER: DATA CONNECTION

Ah - finally!

odhrerir FaxGetty[15611]: GETTY: START "/sbin/getty -h /dev/ttyS1 38400", pid 16858
odhrerir FaxGetty[15611]: GETTY: exit status 01000

Anybody know what this means???  I would dig into it now if
everytime I called in it would try this every other time!

odhrerir FaxGetty[15611]: MODEM ROCKWELL etc.
odhrerir FaxGetty[15611]: ANSWER: FAX CONNECTION
odhrerir FaxGetty[15611]: ANSWER: Ring detected without successful handshake

Ok, after a Data call it should go back to Fax mode.

odhrerir FaxGetty[15611]: MODEM ROCKWELL etc.
odhrerir FaxGetty[15611]: ANSWER: FAX CONNECTION
odhrerir FaxGetty[15611]: ANSWER: Ring detected without successful handshake

Here we go again!

odhrerir FaxGetty[15611]: MODEM ROCKWELL etc.
---------------------------------------------------------------------

I have been thru the HTML docs, and the FAQ but don't grasp anything
that points to my problem.

---------------------------- Small config.ttyS1 ----------------------
# Configuration for a Rockwell RC288DPi-based Class 1 modem.
#    Hayes Optima 28800         firmware rev ???
#    Microcom DeskPorte 28.8S   firmware rev V1.100K-V34_DS
#    PPI PM288FXMT              firmware rev 1.57
#
# Note that the modem does not lock the line rate for fax
# receive (at least not the PM288FXMT); but not sure whether
# current flow control settings are maintained or if it
# switches to XON/XOFF (testing host was too fast to see).
#
CountryCode:            1
AreaCode:               630
FAXNumber:              +1.630.963.0474
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          off
GettyArgs:              "-h /dev/%l %s"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
AdaptiveAnswer:         yes
AnswerRotary:           "fax data"
MaxRecvPages:           25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
ModemRate:              38400           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&K0           # setup no flow control
ModemHardFlowCmd:       AT&K3           # setup hardware flow control
ModemSoftFlowCmd:       AT&K4           # setup software flow control
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)#
ModemMfrQueryCmd:       !Rockwell
ModemModelQueryCmd:     !RC288DPi
ModemRevQueryCmd:       ATI3            # product information
#
ModemDialCmd:           ATDT%s          # T for tone dialing
#
#  Added for Rotating Answer Types
#
ModemAnswerFaxCmd:      AT+FCLASS=1;A   # default is to answer as fax
ModemAnswerDataCmd:     ATH+FCLASS=0;A  # hangup and answer as data
Class1RecvIdentTimer:   10000           # timeout fax answer in 10 secs
-------------------------------------------------------------------------

Basically by the book!  Did I miss something REAL important?

BC
Linux - 
Learn how to read in 15000 easy steps
(refresher course with each kernel 8-)