|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
sendpage nightmare!!
Hello everyone.
I need some help getting sendpage working on the following system.
AMD 486 DX4 100MHz
RedHat 4.0 Linux with 2.0.22 kernel
HylaFAX v4.0pl1
AMD 486 DX/4 100MHzSupraFAXModem 288 with ROM version V1.440-25-V34_DS
USA Mobile NorthEast Ohio Paging Service (1200BPS 7E1 XON/XOFF)
I have been through the mailinglist archives, but none of the examples
I found seem to work. Most would not even get me to the CONNECT 1200
message. My current config is below:
SessionTracing: 4111
ModemType: Class2 # use this to supply a hint
ModemRate: 19200
ModemFlowControl: rtscts # XON/XOFF flow control assumed
#
# USA MOBILE Pager Service Commands
#
PagerSetupCmds: ATE0B0S37=5N0W2&Q6F4
PagerMaxMsgLength: 128
IXOService: ``PG''
IXODeviceID: ``1''
IXOMaxUnknown: 20
IXOIDProbe: 2
IXOIDTimeout: 60
IXOLoginRetries: 3
IXOLoginTimeout: 60
IXOGATimeout: 60
IXOXmitRetries: 4
IXOXmitTimeout: 60
IXOAckTimeout: 60
I have kicked up all the timeout values in an effort to rule out
errors caused by timeouts. I have tried numerous combinations of 1200
to 38400 and XONXOFF and RTSCTS in the ModemRate and ModemFlowControl
fields respectively. In addition, I have tried numerous combinations
on modem commands in the PagerSetupCmds field. The current
configuration is the only one that has gotten me as far as the "ID="
prompt at the pager terminal on numerous occasions. I have attempted
to get technical information from USA Mobile, but all they can tell me
is the connect parameters, and tell me for anymore information to call
the 1-800 number for the software. The terminal access number is
18006889259 and my pager ID is 9813324 if anyone wants to see if the
terminal works with their coniguration. Make sure you include your
e-mail address. Below is a session tracing log for the above
parameters.
Jan 18 14:56:03.37: [10694]: SESSION BEGIN 00000091 18006889259
Jan 18 14:56:03.40: [10694]: SEND PAGE: JOB 36 DEST 18006889259 COMMID 00000091
Jan 18 14:56:03.40: [10694]: MODEM set DTR OFF
Jan 18 14:56:03.40: [10694]: DELAY 2600 ms
Jan 18 14:56:06.01: [10694]: MODEM set DTR ON
Jan 18 14:56:06.01: [10694]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS
Jan 18 14:56:06.01: [10694]: MODEM flush i/o
Jan 18 14:56:06.01: [10694]: <-- [15:ATE0V1Q0S0=0H0\r]
Jan 18 14:56:06.03: [10694]: --> [2:OK]
Jan 18 14:56:06.03: [10694]: <-- [21:ATS8=2S7=90&K3&D2&C1\r]
Jan 18 14:56:06.05: [10694]: --> [2:OK]
Jan 18 14:56:06.05: [10694]: <-- [5:ATM0\r]
Jan 18 14:56:06.06: [10694]: --> [2:OK]
Jan 18 14:56:06.06: [10694]: MODEM set parity: 7 bits, even parity
Jan 18 14:56:06.06: [10694]: MODEM input buffering enabled
Jan 18 14:56:06.36: [10694]: <-- [12:AT+FCLASS=0\r]
Jan 18 14:56:06.47: [10694]: --> [2:OK]
Jan 18 14:56:06.47: [10694]: <-- [21:ATE0B0S37=5N0W2&Q6F4\r]
Jan 18 14:56:06.59: [10694]: --> [2:OK]
Jan 18 14:56:06.59: [10694]: DIAL 18006889259
Jan 18 14:56:06.59: [10694]: <-- [20:ATM2L3DT18006889259\r]
Jan 18 14:56:25.26: [10694]: --> [12:CONNECT 1200]
Jan 18 14:56:25.26: [10694]: EXPECT ID (paging central identification)
Jan 18 14:56:25.26: [10694]: <-- <1:\015>
Jan 18 14:56:26.06: [10694]: --> <3:ID=>
Jan 18 14:56:26.06: [10694]: RECV ID ("ID=")
Jan 18 14:56:26.06: [10694]: SEND device identification/login request
Jan 18 14:56:26.06: [10694]: <-- <13:\033``PG''``1''\015>
Jan 18 14:56:27.06: [10694]: --> <3:ID=>
Jan 18 14:56:27.06: [10694]: RECV: ID=
Jan 18 14:56:35.28: [10694]: --> <24:TDD's Enter M and RETURN>
Jan 18 14:56:35.28: [10694]: RECV: TDD's Enter M and RETURN
Jan 18 14:56:35.28: [10694]: --> <3:ID=>
Jan 18 14:56:35.28: [10694]: RECV: ID=
Jan 18 14:57:16.54: [10694]: --> <10:NO CARRIER>
Jan 18 14:57:16.54: [10694]: RECV: NO CARRIER
Jan 18 14:58:16.54: [10694]: MODEM TIMEOUT: reading line from modem
Jan 18 14:58:16.54: [10694]: PAGE FAILED: Protocol failure: timeout waiting for response from paging central
Jan 18 14:58:16.54: [10694]: <-- [5:ATH0\r]
Jan 18 14:58:16.66: [10694]: --> [2:OK]
Jan 18 14:58:16.66: [10694]: MODEM input buffering enabled
Jan 18 14:58:16.66: [10694]: MODEM set DTR OFF
Jan 18 14:58:16.66: [10694]: SESSION END
I am not really sure if the problem is with my configuration, or with
the paging terminal itself. Any help would be greatly appreciated.
Thanks in advance.
Regards,
Jerry Kinsley
