|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: Short Pages Cut
> Hi. I just installed version 4.0pl1 of hylafax on a Linux machine
> running kernel version 2.0.27. Everything seems to work fine, except
> that, when a dociment sent with sendfax is short (doesn't take up a
> full page of text), the page gets cut after the text, and does not end
> up being an 8.5x11 in page. All the text gets transmitted, but the
> page is cut after the text. Any ideas?
>
> Here is a log from a transmission where this happened.
>
> (I am using a USR Sportster 33.6 FAX modem, running it in Class 1 mode
> -- under a previous version of Hylafax, I could not get Class 2.0 to
> work reliably with this modem).
>
>
>
> Jan 02 13:10:29.37: [ 1723]: SESSION BEGIN 00000008 13065854815
> Jan 02 13:10:29.38: [ 1723]: SEND FAX: JOB 5 DEST 585-4815 COMMID 00000008
> Jan 02 13:10:29.38: [ 1723]: DELAY 2600 ms
> Jan 02 13:10:31.99: [ 1723]: <-- [17:ATE0V1Q0X4S0=0H0\r]
> Jan 02 13:10:32.13: [ 1723]: --> [2:OK]
> Jan 02 13:10:32.13: [ 1723]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
> Jan 02 13:10:32.27: [ 1723]: --> [2:OK]
> Jan 02 13:10:32.27: [ 1723]: <-- [12:AT+FCLASS=1\r]
> Jan 02 13:10:32.41: [ 1723]: --> [2:OK]
> Jan 02 13:10:32.41: [ 1723]: <-- [12:AT&H1&I0&R2\r]
> Jan 02 13:10:32.55: [ 1723]: --> [2:OK]
> Jan 02 13:10:32.55: [ 1723]: <-- [21:AT+FCLASS=0&H1&I0&R2\r]
> Jan 02 13:10:32.69: [ 1723]: --> [2:OK]
> Jan 02 13:10:32.69: [ 1723]: <-- [7:ATL1M1\r]
> Jan 02 13:10:32.83: [ 1723]: --> [2:OK]
> Jan 02 13:10:32.84: [ 1723]: <-- [12:AT+FCLASS=1\r]
> Jan 02 13:10:33.08: [ 1723]: --> [2:OK]
> Jan 02 13:10:33.08: [ 1723]: <-- [12:AT&H1&I0&R2\r]
> Jan 02 13:10:33.32: [ 1723]: --> [2:OK]
> Jan 02 13:10:33.32: [ 1723]: DIAL 5854815
> Jan 02 13:10:33.32: [ 1723]: <-- [12:ATDT5854815\r]
> Jan 02 13:10:51.20: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:52.81: [ 1723]: --> [2:OK]
> Jan 02 13:10:52.81: [ 1723]: <-- [9:AT+FRH=3\r]
> Jan 02 13:10:52.82: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:53.50: [ 1723]: --> [2:OK]
> Jan 02 13:10:53.50: [ 1723]: REMOTE CSI "3065854815"
> Jan 02 13:10:53.50: [ 1723]: <-- [9:AT+FRH=3\r]
> Jan 02 13:10:53.51: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:53.77: [ 1723]: --> [2:OK]
> Jan 02 13:10:53.77: [ 1723]: REMOTE best rate 9600 bit/s
> Jan 02 13:10:53.77: [ 1723]: REMOTE max page width 1728 pixels in 215 mm
> Jan 02 13:10:53.77: [ 1723]: REMOTE max unlimited page length
> Jan 02 13:10:53.77: [ 1723]: REMOTE best vres 7.7 line/mm
> Jan 02 13:10:53.77: [ 1723]: REMOTE best format 2-D MR
> Jan 02 13:10:53.77: [ 1723]: REMOTE best 10 ms, 5 ms/scanline
> Jan 02 13:10:53.77: [ 1723]: USE 9600 bit/s
> Jan 02 13:10:53.77: [ 1723]: USE 10 ms, 5 ms/scanline
> Jan 02 13:10:53.77: [ 1723]: SEND file "docq/doc5.cover;70"
> Jan 02 13:10:53.77: [ 1723]: USE page width 1728 pixels in 215 mm
> Jan 02 13:10:53.77: [ 1723]: USE unlimited page length
> Jan 02 13:10:53.77: [ 1723]: USE 3.85 line/mm
> Jan 02 13:10:53.77: [ 1723]: USE 1-D MR
> Jan 02 13:10:53.77: [ 1723]: SEND training at v.29 9600 bit/s
> Jan 02 13:10:53.77: [ 1723]: <-- [9:AT+FTH=3\r]
> Jan 02 13:10:54.01: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:54.01: [ 1723]: <-- data [23]
> Jan 02 13:10:54.01: [ 1723]: <-- data [2]
> Jan 02 13:10:54.03: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:54.03: [ 1723]: <-- data [6]
> Jan 02 13:10:54.03: [ 1723]: <-- data [2]
> Jan 02 13:10:55.98: [ 1723]: --> [2:OK]
> Jan 02 13:10:55.98: [ 1723]: DELAY 75 ms
> Jan 02 13:10:56.07: [ 1723]: <-- [10:AT+FTM=96\r]
> Jan 02 13:10:56.39: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:56.39: [ 1723]: <-- data [1024]
> Jan 02 13:10:56.39: [ 1723]: <-- data [776]
> Jan 02 13:10:56.39: [ 1723]: <-- data [2]
> Jan 02 13:10:57.92: [ 1723]: --> [2:OK]
> Jan 02 13:10:57.92: [ 1723]: <-- [9:AT+FRH=3\r]
> Jan 02 13:10:58.30: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:59.36: [ 1723]: --> [2:OK]
> Jan 02 13:10:59.36: [ 1723]: TRAINING succeeded
> Jan 02 13:10:59.36: [ 1723]: <-- [10:AT+FTM=96\r]
> Jan 02 13:10:59.79: [ 1723]: --> [7:CONNECT]
> Jan 02 13:10:59.79: [ 1723]: SEND begin page
> Jan 02 13:10:59.80: [ 1723]: <-- data [1028]
> Jan 02 13:10:59.80: [ 1723]: <-- data [1027]
> Jan 02 13:10:59.80: [ 1723]: <-- data [1027]
> Jan 02 13:10:59.80: [ 1723]: <-- data [1024]
> Jan 02 13:10:59.80: [ 1723]: <-- data [1027]
> Jan 02 13:11:00.80: [ 1723]: <-- data [1024]
> Jan 02 13:11:00.80: [ 1723]: <-- data [1026]
> Jan 02 13:11:00.80: [ 1723]: <-- data [1024]
> Jan 02 13:11:01.82: [ 1723]: <-- data [1027]
> Jan 02 13:11:02.87: [ 1723]: <-- data [1026]
> Jan 02 13:11:03.92: [ 1723]: <-- data [1030]
> Jan 02 13:11:03.92: [ 1723]: <-- data [1024]
> Jan 02 13:11:04.97: [ 1723]: <-- data [630]
> Jan 02 13:11:06.07: [ 1723]: SENT 12917 bytes of data
> Jan 02 13:11:06.08: [ 1723]: <-- data [1027]
> Jan 02 13:11:06.08: [ 1723]: <-- data [1024]
> Jan 02 13:11:07.12: [ 1723]: <-- data [1024]
> Jan 02 13:11:08.17: [ 1723]: <-- data [532]
> Jan 02 13:11:08.20: [ 1723]: SENT 3604 bytes of data
> Jan 02 13:11:08.20: [ 1723]: SEND 1D RTC
> Jan 02 13:11:08.20: [ 1723]: <-- data [29]
> Jan 02 13:11:08.20: [ 1723]: <-- data [2]
> Jan 02 13:11:08.20: [ 1723]: SEND end page
> Jan 02 13:11:13.62: [ 1723]: --> [2:OK]
> Jan 02 13:11:13.62: [ 1723]: DELAY 75 ms
> Jan 02 13:11:13.71: [ 1723]: SEND send MPS (more pages, same document)
> Jan 02 13:11:13.71: [ 1723]: <-- [9:AT+FTH=3\r]
> Jan 02 13:11:13.86: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:13.86: [ 1723]: <-- data [3]
> Jan 02 13:11:13.86: [ 1723]: <-- data [2]
> Jan 02 13:11:15.04: [ 1723]: --> [2:OK]
> Jan 02 13:11:15.04: [ 1723]: <-- [9:AT+FRH=3\r]
> Jan 02 13:11:18.14: [ 1723]: --> [0:]
> Jan 02 13:11:18.15: [ 1723]: MODEM <Empty line>
> Jan 02 13:11:18.15: [ 1723]: <-- data [1]
> Jan 02 13:11:18.17: [ 1723]: --> [2:OK]
> Jan 02 13:11:18.17: [ 1723]: SEND send MPS (more pages, same document)
> Jan 02 13:11:18.17: [ 1723]: <-- [9:AT+FTH=3\r]
> Jan 02 13:11:18.20: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:18.20: [ 1723]: <-- data [3]
> Jan 02 13:11:18.20: [ 1723]: <-- data [2]
> Jan 02 13:11:19.38: [ 1723]: --> [2:OK]
> Jan 02 13:11:19.38: [ 1723]: <-- [9:AT+FRH=3\r]
> Jan 02 13:11:19.90: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:20.85: [ 1723]: --> [2:OK]
> Jan 02 13:11:20.85: [ 1723]: SEND recv MCF (message confirmation)
> Jan 02 13:11:20.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (page 1 of 2 sent in 0:27)
> Jan 02 13:11:20.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (docq/doc5.cover;70 sent in 0:27)
> Jan 02 13:11:20.85: [ 1723]: SEND file "docq/doc9.ps;70"
> Jan 02 13:11:20.85: [ 1723]: USE page width 1728 pixels in 215 mm
> Jan 02 13:11:20.86: [ 1723]: USE unlimited page length
> Jan 02 13:11:20.86: [ 1723]: USE 3.85 line/mm
> Jan 02 13:11:20.86: [ 1723]: USE 1-D MR
> Jan 02 13:11:20.86: [ 1723]: <-- [10:AT+FTM=96\r]
> Jan 02 13:11:21.29: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:21.29: [ 1723]: SEND begin page
> Jan 02 13:11:21.30: [ 1723]: <-- data [1029]
> Jan 02 13:11:21.30: [ 1723]: <-- data [1024]
> Jan 02 13:11:21.30: [ 1723]: <-- data [1024]
> Jan 02 13:11:21.30: [ 1723]: <-- data [1024]
> Jan 02 13:11:21.30: [ 1723]: <-- data [1025]
> Jan 02 13:11:22.30: [ 1723]: <-- data [1027]
> Jan 02 13:11:22.30: [ 1723]: <-- data [1025]
> Jan 02 13:11:22.30: [ 1723]: <-- data [1025]
> Jan 02 13:11:23.27: [ 1723]: <-- data [1025]
> Jan 02 13:11:24.32: [ 1723]: <-- data [1026]
> Jan 02 13:11:25.42: [ 1723]: <-- data [1024]
> Jan 02 13:11:25.42: [ 1723]: <-- data [228]
> Jan 02 13:11:26.52: [ 1723]: SENT 11492 bytes of data
> Jan 02 13:11:26.52: [ 1723]: SEND 1D RTC
> Jan 02 13:11:26.52: [ 1723]: <-- data [29]
> Jan 02 13:11:26.52: [ 1723]: <-- data [2]
> Jan 02 13:11:26.52: [ 1723]: SEND end page
> Jan 02 13:11:30.93: [ 1723]: --> [2:OK]
> Jan 02 13:11:30.95: [ 1723]: DELAY 95 ms
> Jan 02 13:11:31.06: [ 1723]: SEND send EOP (no more pages or documents)
> Jan 02 13:11:31.06: [ 1723]: <-- [9:AT+FTH=3\r]
> Jan 02 13:11:31.21: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:31.21: [ 1723]: <-- data [3]
> Jan 02 13:11:31.21: [ 1723]: <-- data [2]
> Jan 02 13:11:32.39: [ 1723]: --> [2:OK]
> Jan 02 13:11:32.39: [ 1723]: <-- [9:AT+FRH=3\r]
> Jan 02 13:11:33.05: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:33.85: [ 1723]: --> [2:OK]
> Jan 02 13:11:33.85: [ 1723]: SEND recv MCF (message confirmation)
> Jan 02 13:11:33.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (page 2 of 2 sent in 0:13)
> Jan 02 13:11:33.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (docq/doc9.ps;70 sent in 0:13)
> Jan 02 13:11:33.85: [ 1723]: <-- [9:AT+FTH=3\r]
> Jan 02 13:11:34.09: [ 1723]: --> [7:CONNECT]
> Jan 02 13:11:34.09: [ 1723]: <-- data [3]
> Jan 02 13:11:34.09: [ 1723]: <-- data [2]
> Jan 02 13:11:35.26: [ 1723]: --> [2:OK]
> Jan 02 13:11:35.26: [ 1723]: <-- [5:ATH0\r]
> Jan 02 13:11:35.49: [ 1723]: --> [2:OK]
> Jan 02 13:11:35.49: [ 1723]: SESSION END
>
>
> Thanks for any help.
>
> Chris Nicol.
>
> (PS: Never had this problem with v 3.0pl1. CN)
> _______________________________________________________________________________
> Dr. Chris Nicol, Economics Phone: (306) 585-4182; FAX: 585-4815
> University of Regina E-Mail: nicolc@elsie.econ.uregina.ca
> Saskatchewan, S4S 0A2, CANADA. nicolc@cas.uregina.ca
Check out pagechop in the config manpage
Tom Szybist
szybist@boxhill.com
